Tuesday, June 23, 2009

Refrigerator uses no power

This refrigerator is an ice box and has no freezer. This guy built it over 20 years ago. He doesn't say what the refrigerant is but he said it boiled at about -20F. That sounds like ammonia to me. Although ammonia boils at -27F. It is a huge box that holds 300 gallons of water and has 16 plus inches of insulation around the tank. The tank is galvanized metal with a plastic liner. Copper tubes filled with ammonia connect to baseboard units that are outside and placed higher than the refrigerator.

So, how it works...

Whenever the temp of the water is greater than -27F then the ammonia is a gas that fills the tubes under slight pressure. When the temperature outside is cold enough (below freezing), the ammonia will condense on the walls of the copper tubing. The condensed ammonia drips down to the fridge where it absorbs the heat from the 300 gallons of water. It then boils to a gas again. The process continues until the water turns into a 300 gallon block of ice. The only moving part is a cutoff valve. It is shut at this point to prevent everything in the fridge from freezing. The ice will last until the next winter, or I should say that some of it will and maintain the fridge temps.

I would take it a few steps forward though. I would design it so that it was like a chest freezer so the door opened on the top. This would make it way more efficient. Then I would let the ice get much colder in the winter and have a fridge and a freezer section. The fridge section would have more insulation between it and the ice so that it doesn't get as cold. The freezer section would have no insulation on the part touching the ice.

Just so you know, 300 gallons take a lot of space and it weighs a lot. It weighs 2500 lbs and takes up 40 cubic feet. If you laid that down so that it was a chest fridge/freezer then you could make the water container 30 inches deep, 70 inches long and 33 inches wide. Then you need 16 inches all around for insulation. It would be a big unit but the storage would be shallow, maybe 13 inches deep for the fridge (so you can get a 2 liter bottle in it standing up). And deeper for the freezer section because that section is submerged with ice around it.

I found this in wikipedia.
In 400 BC Iran, Persian engineers had already mastered the technique of storing ice in the middle of summer in the desert. The ice was brought in during the winters from nearby mountains in bulk amounts, and stored in specially designed, naturally cooled refrigerators, called yakhchal (meaning ice storage). This was a large underground space (up to 5000 m³) that had thick walls (at least two meters at the base) made out of a special mortar called sārooj, composed of sand, clay, egg whites, lime, goat hair, and ash in specific proportions, and which was known to be resistant to heat transfer. This mixture was thought to be completely water impenetrable. The space often had access to a Qanat, and often contained a system of windcatchers which could easily bring temperatures inside the space down to frigid levels on summer days. The ice was then used to chill treats for royalty on such occasions.

Richard

7 comments:

  1. Your refrigerator idea is great but can it produce ice without any water?

    I have an idea for a solar powered refrigerator for hot desert countries which produces ice which can then be melted and used as drinking water.

    ReplyDelete
  2. i love this idea but how to make the hole in the roofing iron? i doubt that i could do this with my tin snips?

    ReplyDelete
  3. Important note:
    Ammonia will corrode copper very quickly.
    Commercial systems, like RV fridges, use soft iron pipe, not copper.
    http://en.wikipedia.org/wiki/Ammonia

    ReplyDelete
  4. Important note:
    Ammonia will very quickly corrode copper and zinc tubing or pipe.
    Commercial systems like this, used in RV's, use soft iron pipe.
    Also, brass fittings will corrode, being made of copper and zinc.
    http://en.wikipedia.org/wiki/Ammonia

    ReplyDelete
  5. I great post, but I thought ammonia cannot be used with copper piping. I stand to be corrected though...

    ReplyDelete
  6. This comment has been removed by a blog administrator.

    ReplyDelete
  7. This comment has been removed by a blog administrator.

    ReplyDelete